จาก 01/Strado
IP:180.183.215.88
อังคารที่ , 10/1/2555
เวลา : 10:25
อ่านแล้ว = ครั้ง
 เก็บเข้ากระทู้ส่วนตัว
 แจ้งลบ
 ส่งหาเพื่อน
|
น้อง Fox ได้บอกว่า 400D hack ISO ได้ถึง 16-3200
ก็เลยลองหาดูใน Google แล้วได้ทดลอง ทั้ง version 2009 จน ล่าสุด version Dec-2011.
เห็นว่าได้ผลดี ก็เลยเอามาบอก ชาว weekend กัน
บางคนอาจจะยังไม่ทราบ เหมือนผม จะได้ไม่ทิ้งไปหาของใหม่
http://code.google.com/p/400plus/
พึ่งลองเมื่อวาน เลยให้เด็กใน ออฟฟิสเป็น หนูทดลอง
Introduction¶This document describes the Installation procedure; if you need information on using the hack, please read the User Guide.
Details¶Before you begin¶In order to install 400plus you are definitively going to need a CF card reader; it is simply not possible to install 400plus through a USB cord attached to your camera.
Preparing the camera¶The following steps prepare your camera to execute 400plus each time it start up; this procedure must be done only once:
1.Use a fully charged battery. You need CF card reader and Windows, Linux or Mac. On a mac you can use the native method or, use Windows under Bootcamp/VMware Fusion or use the Linux method.
2.Update to latest firmware (1.1.1) by copying it into the root of CF with your card reader, then put it in the camera and run "update firmware" in the setup menu.
3.Empty your CF, download testfir.fir and copy it into the root of your CF with the card reader.
4.Insert the CF into the camera and run the firmware update using 'testfir.fir', the screen will go blank then. Wait at least 2 minutes, turn it off, and finally take battery out and back in.
Preparing each card¶The following steps prepare a card to contain 400plus` and be recognized by the camera; this procedure must be done for each card:
1.This step depends on your OS and CF Card, but first insert CF into the camera and format it.
[NOTE: You can format it on the PC too]
◦Windows: use EOScard by pelican, you need to check EOS_DEVELOP and BOOTDISK like shown here.
[NOTE: Some Win7 users reported that no method was working for them; install VirtualBox with Linux LiveCD running on it, and use the Linux method, after attaching the card reader to the VM]
◦Mac: use zeno's MacBoot automated tool (not compatible with Lion).
◦Linux: use the direct method (below) or use the method and files described here (use the second version).
◦Direct method for Linux, Mac, and Windows with cygwin or dd:
■FAT12 / FAT16 (CF Card <= 4GB)
dev=/dev/sdX1 # replace sdX1 with your CF device (first partition) echo EOS_DEVELOP | dd of="$dev" bs=1 seek=43 count=11 echo BOOTDISK | dd of="$dev" bs=1 seek=64 count=8■FAT32
dev=/dev/sdX1 # replace sdX1 with your CF device (first partition) echo EOS_DEVELOP | dd of="$dev" bs=1 seek=71 count=11 echo BOOTDISK | dd of="$dev" bs=1 seek=92 count=8■exFAT
This is not going to work directly, because the sector checksums needs to be calculated and written back after writing the strings. Use the above methods. 2.Download the latest autoexec.bin, extract it, and copy to CF.
3.Put the languages.ini on the CF too, if you want support for additional languages.
4.Insert the CF into camera... and you are done!
If the blue LED of your camera briefly lights up when the camera is turned on, the hack has been successfully loaded.
Updating 400plus¶To update from a previous version of 400plus, just overwrite the autoexec.bin and languages.ini files in all your cards.
Removing 400plus¶The first step of the installation procedure cannot be undone, and the camera will always try to execute 400plus if it is in the CF card; thus, formating all your cards will remove 4000plus for all practical purposes.
|
