คำตอบที่ 271
Type of OBD II DATA PARAMETER LIST
ABS FRP (0 - 65,5350 kPA) or (0 - 95050.5 psi)
Absolute Fuel Rail Pressure is the fuel pressure at the engine in respect to atmospheric
pressure.
ABS LOAD (0 -100%)
Absolute Load Value is the normalized value of air mass per intake stroke in percentage.
ABSLT TPS (0 - 100%)
Absolute Throttle Position represents normalized distance the throttle is opened.
ACC POS D,E or F (0 -100%)
Accelerator Pedal Position represents normalized distance the gas pedal is pressed.
BARO PRESS (0 -255 kPA) or (0 - 36.9 psi)
Barometric Pressure is usually received from a dedicated barometer, manifold absolute
pressure sensor, and other inputs during certain modes of driving.
. The Baro Press may not exhibit the same value as weather services, which
measure barometric pressure at sea level.
CALC LOAD (0 - 100%)
Calculated LOAD Value indicates the normalized load value on the engine.
CAT TEMPxy (- 40 6513.5.C) or ( - 40 9999.9.F)
Catalyst Temperature displays the catalyst substrate temperature for a Bank x catalyst (if
used by control module strategy for OBD monitoring) or displays the Bank x Sensor y
catalyst temperature sensor.
CLR DST (0 65,535 km) or (0 40,722 miles)
Distance Since Cleared Diagnostic Codes is the distance driven since diagnostic trouble
codes were erased.
CLR TIM (0 65,535 min) or (0 1092.25 hours)
Time Since Cleared Diagnostic Code is time since diagnostic trouble codes were erased.
CMD EQ RATxy (0 1.99)
Commanded Equivalence Ratio is the ratio of the air/fuel mixture.
For systems that use conventional oxygen sensors, the commanded equivalence
ratio displays in open loop. In closed loop, the value is 1.0.
Fuel systems using wide-range/linear oxygen sensors display commanded equivalence
ratio in both open and closed loop operation.
COOLANT (-40 215.C) or (- 40 419.F)
Coolant displays engine coolant temperature (ECT) from a ECT sensor or cylinder head
temperature sensor.
. Many diesel engines do not use either sensor and may substitute Engine Oil
Temperature instead.
EGR CMD (0 100%)
Commanded Exhaust Gas Recirculation is the normalized percentage of exhaust gas
being recirculated.
EGR ERR (-100 99.22%)
Exhaust Gas Recirculation Error shows the error from changing from one condition to
another.
ENG RUN (0 65,535 sec.)
Time since Engine Start is the time the engine is running.
. ENG RUN stops when engine stalls or engine is turned off for any reason.
ENGINE (0 16,383.75 RPM)
Engine is the speed engine is running in revolutions per minute (RPM).
EQ RATxy
O2 Sensor Equivalence Ratio is used for linear or wide-ratio oxygen sensors for Bank x
Sensor y.
EVAP REQ (0 100%)
Commanded Evaporative Purge is the position evaporative purge control valve is open in
percentage.
EVAP VP (-8192 8191 PA) or (-32.8878 32.8838 H20)
Evaporative E missions System Vapor Pressure is pressure in the fuel tank
FUEL LVL (0 100%)
Fuel Level Input is the percentage of fuel with 0% equaling tank is full and 100% when
tank is empty.
FUEL PRES (0 765 kPa) or (0 - 110 psi)
Fuel Rail Pressure is the fuel pressure at the engine when reading in reference to atmosphere
pressure.
FUEL SYS (OPEN or CLSD)
Fuel System Status show loop status of fuel system banks.
OPEN: Module is operating in Open Loop control strategy. The vehicle has not yet
satisfied conditions for Module to go to closed loop.
CLSD: PCM currently functioning in Closed loop control strategy, using O2 sensor(
s) as feedback for fuel control
OPEN1: Open Loop control strategy is being used by the PCM due to driving conditions.
Driving conditions that may cause this to happen are power enrichment and deceleration enrichment.
OPEN2: The PCM is operating in Open Loop control strategy due to detected system
fault. Certain actuator or sensor faults will cause module to use an open loop
strategy.
CLSD1: Closed Loop control is current storage being used by module, but a fault
with at least one O2 sensor has been detected. The control system may be
using single O2 for fuel control calculations.
IAT TEMP (- 40 215.C) or (-40 419.F)
Intake Air Temperature is a measure of intake air temperature to determine correct air/fuel
ratios and spark timing operations.
IGN ADV (- 64 63.5.)
Ignition Timing Advance for cylinder is a signal of how much spark advance to add to base
engine timing (expressed in crankshaft degrees).
LT FL FTRM (-100 99.22%)
Long Term Fuel Trim Bank is the fuel mixture adjustment. The mixture can range, with midpoint
being 0.
.
Positive reading indicates module commanded a long-term rich mixture correction
in response to a lean operating condition. A negative reading indicates
module has commanded a long-term lean mixture in response to a rich operating
condition.
MAF (0 655.35 g/s) or (0 86.5 lb/min)
Mass Air Flow Rate indicates the mass of air entering engine.
MAP (0 255 kPa) or (Hg)
Intake Manifold Absolute Pressure displays manifold pressure.
MIL DIST (0 65,535 km) or (0 40,722 miles)
Distance Traveled while Malfunction Indicator Lamp is Active is a counter that displays distance
traveled since the MIL or Check Engine or Service Engine Soon light came on.
MIL STAT (ON or OFF)
Monitor Status Data Trouble Code state that module is commanding Malfunction Indicator
Lamp to be on if problem exists.
MIL TIME (0 65,535 min) or (0 1092.25Hrs)
Distance Since Monitor Status Data Trouble Code is the distance traveled since the MIL
or Check Engine or Service Engine Soon light came on.
O2Sxy (0 1.275V)
Oxygen Sensor Output Voltage is the voltage generated from the oxygen sensor to
increase and decrease the amount of exhaust gas.
O2Sxy (-128 127.996mA)
Oxygen Sensor Output Amp is used for linear or wide ratio oxygen sensors to increase
and decrease the amount of exhaust gas
OBD2 STAT (CA, OBDI, US, NONE, EU and/or JA)
On Board Diagnostic shows what vehicle was made for.
CA - Indicates test vehicle meets California on board diagnostic ARB requirements
OBD I - Indicates test vehicle does not meet OBDII requirements.
US - Indicates test vehicle meets Federal EPA requirements.
NONE - Indicates test vehicle is not on board diagnostic compliant.
EU -Indicates test vehicle meets European on board diagnostic requirement.
JA -Indicates test vehicle meets Japanese on board diagnostic requirement.
OUTSID AIR (- 40 215.C) or (- 40 419.F)
Outside Air Temperature gives temperature outside.
PTO STATUS (OFF or ON)
Power Take Off Status allows module to keep track of Power at Take-Off.
REL FRP (0 5177.27 kPa) or (0 750. psi)
Relative Fuel Rail Pressure (Vacuum) is the fuel rail pressure at engine.
REL TPS (0 100%)
Relative Throttle Position is the normalized relative throttle position.
SECOND AIR (AIR_STAT: UPS, DNS or OFF)
Commanded Secondary Air Status is on newer vehicles and actuators to control pollution
control.
UPS - UP STREAM module is demanding that secondary air be added at exhaust
manifolds
DNS -DOWN STREAM module is demanding secondary air be added at catalytic
converter
OFF -Module is demanding no secondary air to be added.
ST FTRMxy (- 100 99.22%)
Short-term Fuel Trim Bank calculated value represents the short-term relation of fuel metering
on a fuel-injected engine.
. Short-term Fuel Trim calculated value that has a positive percentage is a rich
fuel trim and if a negative percentage is present the fuel trim is lean.
ST FLTRMx (- 100 99.2%)
Short-term Fuel Trim value represents the short-term relation of fuel metering on a
fuel-injected engine.
. Short-term Fuel Trim value with a positive percentage is a rich fuel trim and if
a negative percentage is present the fuel trim is lean.
THR POS (0 100%)
Absolute Throttle Position is the position the throttle is located. The more the throttle is
closed the less percent shown.
THROT CMD (0 100%)
Commanded Throttle Actuator Control is the position of the throttle. If throttle is closed the
percent will be 0 and if wide open 100%.
TRIPS SNC CLR (0 255)
Number of warm-ups since diagnostic trouble codes cleared. Warm-up is when temperature
of coolant rises to at least 22.C (40.F) from engine starting and reaching a minimum
temperature of 70.C (160.F). In a diesel engine, the minimum temperature is 60.C (140.F.)
.
If there is more than 255 that the engine warms up the TRIPS SNC CLR will
remain at 255.
TROUB CODE (0000 FFFF)
Trouble Code Parameter will give the diagnostic trouble code that caused a freeze frame
capture. This information is helpful in diagnosing the cause of a driveability. If no freeze
frame data has been captured, this PID will be zero.
VEH SPEED (0 255 K/h) or (0 158 mph)
Vehicle Speed shows the speed the vehicle is going.
VPWR (0 - 65.535V)
